Noduino I2C Scan
来自Jack's Lab
（版本间的差异）
(→编译烧写) |
(→硬件准备) |
||
| （未显示1个用户的1个中间版本） | |||
| 第12行： | 第12行： | ||
== 硬件准备 == | == 硬件准备 == | ||
| − | + | 此传感器为 I2C 接口，Falcon 接线方式如下： | |
| − | * | + | * Sensor_SCL --> Noduino_Falcon_D9 |
| − | * | + | * Sensor_SDA --> Noduino_Falcon_D8 |
| − | |||
| + | * Sensor_3V3 --> Noduino_Falcon_3V3 | ||
| + | * Sensor_GND --> Noduino_Falcon_GND | ||
| − | |||
| + | NodeC / SmartNode 接线方式如下： | ||
| + | * Sensor_SCL --> SmartNode_IO5 | ||
| + | * Sensor_SDA --> SmartNode_IO4 | ||
| + | |||
| + | |||
| + | * Sensor_3V3 --> SmartNode_3V3 | ||
| + | * Sensor_GND --> SmartNode_GND | ||
<br><br> | <br><br> | ||
| 第102行： | 第109行： | ||
<source lang=cpp> | <source lang=cpp> | ||
| + | #include "noduino.h" | ||
| + | |||
| + | void setup() | ||
| + | { | ||
| + | serial_begin(115200); | ||
| + | wire_begin(); | ||
| + | } | ||
| + | |||
| + | void loop() | ||
| + | { | ||
| + | byte error, address; | ||
| + | int nDevices; | ||
| + | |||
| + | serial_printf("I2C Scanning...\r\n"); | ||
| + | |||
| + | nDevices = 0; | ||
| + | for (address = 1; address < 127; address++) { | ||
| + | // The i2c_scanner uses the return value of | ||
| + | // the wire_endTransmisstion to see if | ||
| + | // a device did acknowledge to the address. | ||
| + | wire_beginTransmission(address); | ||
| + | error = wire_endTransmission(); | ||
| + | |||
| + | if (error == 0) { | ||
| + | serial_printf("I2C device found at address 0x%02X\r\n", address); | ||
| + | nDevices++; | ||
| + | } else if (error == 4) { | ||
| + | serial_printf("Unknow error at address 0x%02X\r\n", address); | ||
| + | } | ||
| + | } | ||
| + | if (nDevices == 0) | ||
| + | serial_printf("No I2C devices found\r\n"); | ||
| + | else | ||
| + | serial_printf("done\r\n"); | ||
| + | delay(25*1000); | ||
| + | } | ||
</source> | </source> | ||
2016年11月14日 (一) 10:30的最后版本
目录 |
[编辑] 1 开发环境准备
根据您的系统，选择如下快速指南：
- Getting Started with Noduino SDK on Linux
- Getting Started with Noduino SDK on Mac OS X
- Getting Started with Noduino SDK on Windows
[编辑] 2 硬件准备
此传感器为 I2C 接口，Falcon 接线方式如下：
- Sensor_SCL --> Noduino_Falcon_D9
- Sensor_SDA --> Noduino_Falcon_D8
- Sensor_3V3 --> Noduino_Falcon_3V3
- Sensor_GND --> Noduino_Falcon_GND
NodeC / SmartNode 接线方式如下：
- Sensor_SCL --> SmartNode_IO5
- Sensor_SDA --> SmartNode_IO4
- Sensor_3V3 --> SmartNode_3V3
- Sensor_GND --> SmartNode_GND
[编辑] 3 编译烧写
进入你的 i2c-scan 目录：
$ cd /PATH/TO/noduino-sdk/examples/noduino/i2c-scan
编译、上传一步完成：
$ make flash
不同平台下，你的串口设备号可能不一样，确认一下你的串口设备，Linux 下 Falcon 开发板可能被识别为 /dev/ttyUSB1（dmesg 查看），则:
$ make flash ESPPORT=/dev/ttyUSB1
Windows 下 Falcon 开发板可能被识别为 COM6（控制面板 --> 设备管理器里查看），则:
$ make flash ESPPORT=COM6
[编辑] 4 查看结果
上传完之后，用串口工具，用 115200 的波特率打开串口，即可看到串口在持续输出传感器测得的值：
Windows 下可用串口调试助手这类插看
Linux 下推荐使用 picocom:
$ sudo apt-get install picocom $ picocom -b 115200 /dev/ttyUSB1 picocom v1.7 port is : /dev/ttyUSB2 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv imap is : omap is : emap is : crcrlf,delbs, Terminal ready ...... ......
Ctrl + a q 退出 picocom
[编辑] 5 代码示例
#include "noduino.h"
void setup()
{
serial_begin(115200);
wire_begin();
}
void loop()
{
byte error, address;
int nDevices;
serial_printf("I2C Scanning...\r\n");
nDevices = 0;
for (address = 1; address < 127; address++) {
// The i2c_scanner uses the return value of
// the wire_endTransmisstion to see if
// a device did acknowledge to the address.
wire_beginTransmission(address);
error = wire_endTransmission();
if (error == 0) {
serial_printf("I2C device found at address 0x%02X\r\n", address);
nDevices++;
} else if (error == 4) {
serial_printf("Unknow error at address 0x%02X\r\n", address);
}
}
if (nDevices == 0)
serial_printf("No I2C devices found\r\n");
else
serial_printf("done\r\n");
delay(25*1000);
}
[编辑] 6 扩展阅读
- 更多问题参考：
