Eagle Tips
(→过孔和线宽与电流关系) |
(→过孔和线宽与电流关系) |
||
第104行: | 第104行: | ||
== 过孔和线宽与电流关系 == | == 过孔和线宽与电流关系 == | ||
− | + | === 线宽 === | |
− | + | 铜厚 1oz (0.035mm),线宽单位 mil (0.0254mm): | |
* 6mil 0.2A | * 6mil 0.2A | ||
第112行: | 第112行: | ||
* 12mil 0.8A | * 12mil 0.8A | ||
* 16mil 1.1A | * 16mil 1.1A | ||
+ | * 1mm 2.3A | ||
+ | * 2mm 4A | ||
− | + | 一般认为 20mil 走线可以过1A电流(有一定余量),设计时需要小于该值的一半考虑。 | |
− | |||
RT5350F全开时电流为280mA,约为3.3V * 0.28A = 0.924W | RT5350F全开时电流为280mA,约为3.3V * 0.28A = 0.924W | ||
第121行: | 第122行: | ||
其中天线发射功率为100mW,大概40mA的电流,用6mil的导线就够了。 | 其中天线发射功率为100mW,大概40mA的电流,用6mil的导线就够了。 | ||
− | + | ||
+ | 过孔的对应的导线宽度为焊盘边缘宽度,即10mil的孔,16mil的焊盘外径则对应6mil的导线。 | ||
+ | |||
+ | <br> | ||
+ | |||
+ | === 过孔 === | ||
+ | |||
+ | 0.5mm(20mil)过孔可以过1A电流(有一定余量) | ||
+ | |||
+ | 如果 2A 电流放置 0.25mm(10mil)过孔作为载流,至少放置四个过孔 | ||
+ | |||
+ | 接地过孔必须可以承受约 0.5A 的电流,所以 16mil 的过孔至少要 6个,越多越好 | ||
<br><br> | <br><br> |
2021年11月23日 (二) 11:34的版本
目录 |
1 Notes
- 力创的喷锡 PCB,2.54mm 的插针,钻孔必须为 0.9mm,0.7mm 的只能用在镀金板上!2.54mm间距的母座可用0.7mm的喷锡孔
- 力创的丝印,最小最好为 24mil, Ratio 14%
- Eagle Lib: 封装的 name 和 value 建议字符格式:vector, 16mil 8%
- Eagle Lib 字符的 name 建议:50mil, 8%
- 力创开卡槽,可能用的 0.5mm 的铣刀,因此如果是 5mm x 1mm 的槽,最好开成 5.5 - 6 mm x 1mm
力创邮票孔:
开孔最小 0.6mm,孔心到孔芯最小 1mm
力创半孔工艺:
设计时要用 PAD 焊盘孔绘制,把焊盘一半放边框线上,离边距离最低要 2MM 以上如下图:https://www.jlc.com/portal/server_guide_70.html
半孔大小范围:直径≥0.6MM,孔边到孔边≥0.6MM(单边焊环 0.127mm 以上,小于此参数工程会适当优化)
FR-4 板材参数:
- 介电常数 (Dielectric Constant): 4.58
- 介质损耗 (Loss Tangent): 0.022
- 1oz 铜,厚 0.035mm (35um)
http://www.kblaminates.com/chs/upfile/2010123017220691104.pdf
2 Change Fonts
Two steps: First smash all the parts to make sure you can access the part names, then change the font and ratio.
To smash all the parts, try:
display none tOrigin bOrigin; group all; smash (>0 0); display last;
To change the font and ratio, try:
display none tNames bNames; group all; change font vector (>0 0); change ratio 15 (>0 0); display last;
3 Export wiki
Run the DP_Exporter.ulp to create Board and Schematic PNG, a HTML table and WIKI table format:
- Load a board (You must be in the board screen, not in schematic to run the script)
- From File->Run load up DP_Exporter.ulp
4 Export BOM from brd
Run the 204BRD2XLS.ULP to create the BOM list of the *.brd file
5 Export Silkscreen to PDF
Open *.brd file
5.1 Top
display none tNames Dimension print
5.2 Bottom
display none bNames Dimension print
6 Export mnt
run mountsmt.ulp
7 过孔和线宽与电流关系
7.1 线宽
铜厚 1oz (0.035mm),线宽单位 mil (0.0254mm):
- 6mil 0.2A
- 8mil 0.55A
- 12mil 0.8A
- 16mil 1.1A
- 1mm 2.3A
- 2mm 4A
一般认为 20mil 走线可以过1A电流(有一定余量),设计时需要小于该值的一半考虑。
RT5350F全开时电流为280mA,约为3.3V * 0.28A = 0.924W
其中天线发射功率为100mW,大概40mA的电流,用6mil的导线就够了。
过孔的对应的导线宽度为焊盘边缘宽度,即10mil的孔,16mil的焊盘外径则对应6mil的导线。
7.2 过孔
0.5mm(20mil)过孔可以过1A电流(有一定余量)
如果 2A 电流放置 0.25mm(10mil)过孔作为载流,至少放置四个过孔
接地过孔必须可以承受约 0.5A 的电流,所以 16mil 的过孔至少要 6个,越多越好
8 3D 模型库