Getting Started with Noduino SDK on Mac OS X
来自Jack's Lab
1 准备
准备一块 Noduino Falcon / nodemcu v1.0 开发板，一根 micro USB 连接线：
开发板使用 CP2102 这颗 USB 转串口芯片，到芯片厂家官网下载 Mac OS X 版的驱动：http://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx
下载后安装，插上开发板，就能发现：
$ sudo dmesg|tail -n 27 hfs: unmount initiated on Recovery HD on device disk0s3 USB (XHCI Root Hub USB 2.0 Simulation):Port 1 on bus 0xa connected or disconnected: portSC(0xe0206e1) com_silabs_driver_CP210xVCPDriver: init com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::attach com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::probe com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::detach com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::attach com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::start - Registered for Power Management com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::start! com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::start - Found device at interface 0 com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::setPowerState - Waking up com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::SelectInterfaces - BulkInput Pipe is 0xffffff8031e15480 on EP1 com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::SelectInterfaces - BulkOutput Pipe is 0xffffff802bac6900 on EP1 com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::GetCP210xInfo - Part Number Found: 0x02 com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::GetCP210xInfo - UsbConfigurationDescriptor - com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::GetCP210xInfo .bLength = 9 com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::GetCP210xInfo .bDescriptorType = 0x02 com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::GetCP210xInfo .wTotalLength = 32 com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::GetCP210xInfo .bNumInterfaces = 1 com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::GetCP210xInfo .bConfigurationValue = 1 com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::GetCP210xInfo .iConfiguration = 0 com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::GetCP210xInfo .bmAttributes = 0x80 com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::GetCP210xInfo .MaxPower = 50 com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::start - Sucessfully loaded the driver com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::message com_silabs_driver_CP210xVCPDriver(0xffffff8039194000)::message com_silabs_driver_CP210xVCPDriver::setPowerState(0x193cbab37128ae0d, 0 -> 1) timed out after 10205 ms
2 尝试 Noduino SDK
# clone the whole sdk $ git clone git://github.com/icamgo/noduino-sdk.git noduino-sdk # fetch the toolchain of esp8266 $ cd noduino-sdk $ git submodule init $ git submodule update $ cd toolchain $ ./gen.py # generate the toolchain (you need Python 2.7)
尝试点灯的例子
# try the first example $ cd ../example/blink $ make # upload the example to dev board through serial $ make flash
上传完之后，你会很快看到板子靠近 USB 口的 LED 开始在慢闪（大概 2s 间隔）
