Noduino BMP180
来自Jack's Lab
目录 |
1 开发环境准备
根据您的系统,选择如下快速指南:
- Getting Started with Noduino SDK on Linux
- Getting Started with Noduino SDK on Mac OS X
- Getting Started with Noduino SDK on Windows
2 硬件准备
此传感器为 I2C 接口,接线方式如下:
- SCL --> D9
- SDA --> D8
3.3V 供电
3 编译烧写
进入你的 bmp180 目录:
$ cd /PATH/TO/noduino-sdk/examples/noduino/bmp180
编译、上传一步完成:
$ make flash
不同平台下,你的串口设备号可能不一样,确认一下你的串口设备,Linux 下 Falcon 开发板可能被识别为 /dev/ttyUSB1(dmesg 查看),则:
$ make flash ESPPORT=/dev/ttyUSB1
Windows 下 Falcon 开发板可能被识别为 COM6(控制面板 --> 设备管理器里查看),则:
$ make flash ESPPORT=COM6
4 查看结果
上传完之后,用串口工具,用 115200 的波特率打开串口,即可看到串口在持续输出传感器测得的值:
Windows 下可用串口调试助手这类插看
Linux 下推荐使用 picocom:
$ sudo apt-get install picocom $ picocom -b 115200 /dev/ttyUSB1 picocom v1.7 port is : /dev/ttyUSB2 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv imap is : omap is : emap is : crcrlf,delbs, Terminal ready ...... ......
Ctrl + a q 退出 picocom
5 代码示例
#include "noduino.h" #include "bmp180.h" irom void setup() { serial_begin(115200); if (!bmp180_begin()) { serial_print("Could not find a valid BMP180 sensor,\ check wiring!\r\n"); while (1) {} } } irom void loop() { char obuf[16]; double t = 0, p = 0; bmp180_startTemperature(); delay(15); bmp180_getTemperature(&t); dtostrf(t, 16, 2, obuf); serial_printf("Temperature = \t\t%s C\r\n", obuf); bmp180_startPressure(1); delay(15); bmp180_getPressure(&p, &t); dtostrf(p, 16, 2, obuf); serial_printf("Pressure = \t\t%s mbar\r\n", obuf); dtostrf(bmp180_sealevel(p, 50), 16, 2, obuf); // Calculate altitude assuming 'standard' barometric // pressure of 1013.25 millibar = 101325 Pascal serial_printf("Pressure at sealevel (calculated) = %s mbar\r\n", obuf); // you can get a more precise measurement of altitude // if you know the current sea level pressure which will // vary with weather and such. If it is 1015 millibars // that is equal to 101500 Pascals. dtostrf(bmp180_altitude(p, bmp180_sealevel(p, 50)), 16, 2, obuf); serial_printf("Real altitude = \t%s M\r\n\r\n", obuf); delay(3000); }
6 扩展阅读
- 更多问题参考: