Noduino I2C Scan

来自Jack's Lab
2016年11月14日 (一) 10:30Comcat (讨论 | 贡献)的版本

(差异) ←上一版本 | 最后版本 (差异) | 下一版本→ (差异)
跳转到: 导航, 搜索

目录

1 开发环境准备

根据您的系统,选择如下快速指南:




2 硬件准备

此传感器为 I2C 接口,Falcon 接线方式如下:

  • Sensor_SCL --> Noduino_Falcon_D9
  • Sensor_SDA --> Noduino_Falcon_D8


  • Sensor_3V3 --> Noduino_Falcon_3V3
  • Sensor_GND --> Noduino_Falcon_GND


NodeC / SmartNode 接线方式如下:

  • Sensor_SCL --> SmartNode_IO5
  • Sensor_SDA --> SmartNode_IO4


  • Sensor_3V3 --> SmartNode_3V3
  • Sensor_GND --> SmartNode_GND



3 编译烧写

进入你的 i2c-scan 目录:

$ cd /PATH/TO/noduino-sdk/examples/noduino/i2c-scan


编译、上传一步完成:

$ make flash

不同平台下,你的串口设备号可能不一样,确认一下你的串口设备,Linux 下 Falcon 开发板可能被识别为 /dev/ttyUSB1(dmesg 查看),则:

$ make flash ESPPORT=/dev/ttyUSB1


Windows 下 Falcon 开发板可能被识别为 COM6(控制面板 --> 设备管理器里查看),则:

$ make flash ESPPORT=COM6



4 查看结果

上传完之后,用串口工具,用 115200 的波特率打开串口,即可看到串口在持续输出传感器测得的值:


Windows 下可用串口调试助手这类插看


Linux 下推荐使用 picocom:

$ sudo apt-get install picocom
$ picocom -b 115200 /dev/ttyUSB1
picocom v1.7

port is        : /dev/ttyUSB2
flowcontrol    : none
baudrate is    : 115200
parity is      : none
databits are   : 8
escape is      : C-a
local echo is  : no
noinit is      : no
noreset is     : no
nolock is      : no
send_cmd is    : sz -vv
receive_cmd is : rz -vv
imap is        : 
omap is        : 
emap is        : crcrlf,delbs,

Terminal ready

......
......


Ctrl + a q 退出 picocom




5 代码示例

#include "noduino.h"

void setup()
{
	serial_begin(115200);
	wire_begin();
}

void loop()
{
	byte error, address;
	int nDevices;

	serial_printf("I2C Scanning...\r\n");

	nDevices = 0;
	for (address = 1; address < 127; address++) {
		// The i2c_scanner uses the return value of
		// the wire_endTransmisstion to see if
		// a device did acknowledge to the address.
		wire_beginTransmission(address);
		error = wire_endTransmission();

		if (error == 0) {
			serial_printf("I2C device found at address 0x%02X\r\n", address);
			nDevices++;
		} else if (error == 4) {
			serial_printf("Unknow error at address 0x%02X\r\n", address);
		}
	}
	if (nDevices == 0)
		serial_printf("No I2C devices found\r\n");
	else
		serial_printf("done\r\n");

	delay(25*1000);
}




6 扩展阅读

更多问题参考:








个人工具
名字空间

变换
操作
导航
工具箱