Noduino OLED
来自Jack's Lab
(版本间的差异)
(→概述) |
(→概述) |
||
第1行: | 第1行: | ||
== 概述 == | == 概述 == | ||
− | + | SSD1306 驱动芯片 OLED 屏, I2C 接口 | |
<br><br> | <br><br> |
2016年8月28日 (日) 11:06的版本
目录 |
1 概述
SSD1306 驱动芯片 OLED 屏, I2C 接口
2 开发环境准备
根据您的系统,选择如下快速指南:
- Getting Started with Noduino SDK on Linux
- Getting Started with Noduino SDK on Mac OS X
- Getting Started with Noduino SDK on Windows
3 硬件准备
接线方式如下:
- SCL --> D9
- SDA --> D8
3.3V 供电
4 编译烧写
进入你的 u8glib/HelloWorld/ 目录:
$ cd /PATH/TO/noduino-sdk/examples/noduino/u8glib/HelloWorld/
编译、上传一步完成:
$ make flash
不同平台下,你的串口设备号可能不一样,确认一下你的串口设备,Linux 下 Falcon 开发板可能被识别为 /dev/ttyUSB1(dmesg 查看),则:
$ make flash ESPPORT=/dev/ttyUSB1
Windows 下 Falcon 开发板可能被识别为 COM6(控制面板 --> 设备管理器里查看),则:
$ make flash ESPPORT=COM6
5 查看结果
上传完之后,用串口工具,用 115200 的波特率打开串口,即可看到串口在持续输出传感器测得的值:
Windows 下可用串口调试助手这类插看
Linux 下推荐使用 picocom:
$ sudo apt-get install picocom $ picocom -b 115200 /dev/ttyUSB1 picocom v1.7 port is : /dev/ttyUSB2 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv imap is : omap is : emap is : crcrlf,delbs, Terminal ready ...... ......
Ctrl + a q 退出 picocom
6 代码示例
#include "noduino.h" #include "compile.h" #include "U8glib.h" U8GLIB_SSD1306_128X64 u8g(U8G_I2C_OPT_NONE); // I2C / TWI irom void draw(void) { u8g.setFont(u8g_font_unifont); u8g.drawStr(0, 22, "Hello World!"); } irom void setup(void) { // assign default color value if (u8g.getMode() == U8G_MODE_R3G3B2) { u8g.setColorIndex(255); // white } else if (u8g.getMode() == U8G_MODE_GRAY2BIT) { u8g.setColorIndex(3); // max intensity } else if (u8g.getMode() == U8G_MODE_BW) { u8g.setColorIndex(1); // pixel on } else if (u8g.getMode() == U8G_MODE_HICOLOR) { u8g.setHiColorByRGB(255, 255, 255); } serial_begin(115200); serial_printf("%s\r\n", UTS_VERSION); } void loop(void) { // picture loop u8g.firstPage(); do { draw(); } while (u8g.nextPage()); draw(); // rebuild the picture after some delay delay(50); }
更多参考示例位于:noduino-sdk/blob/master/examples/noduino/u8glib/ 下,有显示 Logo、位图、缩放、旋转、动画。。。
7 扩展阅读
- 更多问题参考: