Noduino OpenOnoff

来自Jack's Lab
2016年10月26日 (三) 17:39Comcat (讨论 | 贡献)的版本

跳转到: 导航, 搜索

目录

1 Overview

Open-onoff-3.jpg

Open-onoff-2.jpg


  • AC 85V - 250V General Power Switch
  • ESP8285 inside
  • 250V 10A relay
  • Mainboard size 53mm x 28mm x 17.8mm(H)
  • Shell size 63mm x 33mm x 21mm(H)





2 Quick Start

Open-onoff-4-en.jpg


Maike-wifi-ctrl-2233-all-en.jpg


We need the WeChat to setup the OpenOnoff :)


  • Power off, put the controller join circuit.
  • Link OUTPUT port to the lamp or other electrical appliances under 1KW.
  • Check the connection since it's 220V/110V. It would be best to reinforce the connection points with home insulation tape.
  • Link INPUT port to the home electric supply. (Be Careful, suggest to off the home main breaker)
  • Power on, controller will be waiting for network connection with indicator light flash slowly. (If there is no flash, please press the button for 10sec)
  • Mobile connect to WiFi, scan the QR code in WeChat to connect network.
  • Enter WiFi password, waiting for network connection. (P.S. only 2.4G WiFi is applicable, 5G WiFi and Enterprise - level security certifications are not supportable.)
  • Finish WiFi configuration, WeChat will be in LAN devices matching mode with devices list visible.
  • Click the first device then press "Link Device" button to bind the device. (P.S. if the device has been binding, then the button at bottom is "Enter Official Account"
  • Finish above steps, please press "Enter Official Account" button then click "My Device" button to find your binding devices list. Click the device to enter control page.


If more people need to control the device, please connect to the same router and scan the same QR code while the device is power on. Click "Device connected and skip" -> "Link Device"->"Enter Official Account" to control smart devices


Note
  • Press the button momentarily, manual switch controller
  • Press the button 10sec, restore the factory settings.



3 Open API



4 Hacking

4.1 Prepare firmware

Get noduino-sdk:

$ git clone --recursive git://github.com/icamgo/noduino-sdk.git noduino-sdk


Generate toolchain (you need Python 2.7):

$ cd noduino-sdk/toolchain
$ ./gen.py

Compile the firmware:

$ cd ../sketch/open-onoff
$ make


The generated firmware is located in build/ dir named user1.bin annnd user2.bin


Window environment please refer to Getting Started with Noduino SDK on Windows, you can get how to setup the basic developmennt environment



4.2 Upload

4.2.1 Serial

5pin.jpg


Ft232.jpg


  • USB2UART_GND ------> SmartNode_GPIO0
  • USB2UAR_GND -----> SmartNode_GND
  • USB2UAR_RXD -----> SmartNode_TX
  • USB2UAR_TXD -----> SmartNode_RX


Connect USB2UAR_VCC3.3 -----> SmartNode_VCC at last

ESP8285 will be enter upload mode, we can upload the compiled firmware through serial using following commands in Linux:

$ cd /path/to/noduino-sdk/sketch/open-onoff
$ make produce ESPPORT=/dev/ttyUSB1


In windows:

$ make produce ESPPORT=COM7

COM7 is your USB2UART device


In MAC OS, maybe it's:

$ make produce ESPPORT=/dev/cu.SLAB_USBtoUART

/dev/cu.SLAB_USBtoUART is your USB2UART device



4.2.2 Online

Access
http://dev.noduino.org/openonoff


Login
  • Username: noduino
  • password: noduino1234


Click the "Add files", select the user1.bin and user2.bin located in /path/to/noduino-sdk/sketch/open-plug/build/


Then click "Start upload" to upload the user1.bin and user2.bin into the server temporaily



5 Hardware

OpenOnoff-V1.0-sch.png]


OpenOnoff-V1.0-layout.png





























个人工具
名字空间

变换
操作
导航
工具箱