Noduino PCF8563
来自Jack's Lab
(版本间的差异)
(→编译烧写) |
(→硬件准备) |
||
(未显示1个用户的1个中间版本) | |||
第18行: | 第18行: | ||
== 硬件准备 == | == 硬件准备 == | ||
− | 此传感器为 I2C | + | 此传感器为 I2C 接口,Falcon 接线方式如下: |
− | * | + | * Sensor_SCL --> Noduino_Falcon_D9 |
− | * | + | * Sensor_SDA --> Noduino_Falcon_D8 |
− | |||
+ | * Sensor_3V3 --> Noduino_Falcon_3V3 | ||
+ | * Sensor_GND --> Noduino_Falcon_GND | ||
+ | |||
+ | NodeC / SmartNode 接线方式如下: | ||
+ | |||
+ | * Sensor_SCL --> SmartNode_IO5 | ||
+ | * Sensor_SDA --> SmartNode_IO4 | ||
+ | |||
+ | |||
+ | * Sensor_3V3 --> SmartNode_3V3 | ||
+ | * Sensor_GND --> SmartNode_GND | ||
<br><br> | <br><br> | ||
第105行: | 第115行: | ||
<source lang=cpp> | <source lang=cpp> | ||
+ | #include "noduino.h" | ||
+ | #include "pcf8563.h" | ||
+ | |||
+ | irom void setup() | ||
+ | { | ||
+ | serial_begin(115200); | ||
+ | pcf8563_init(); | ||
+ | pcf8563_set_from_int(2016, 8, 28, 12, 0, 0); | ||
+ | |||
+ | serial_printf("PCF8563 RTC Example!\r\n"); | ||
+ | } | ||
+ | void loop() | ||
+ | { | ||
+ | pcf8563_now(); | ||
+ | pcf8563_print(); | ||
+ | delay(2000); | ||
+ | } | ||
</source> | </source> | ||
2016年11月14日 (一) 10:29的最后版本
目录 |
[编辑] 1 概述
PCF8563 I2C 口 RTC 芯片,超小封装,超低功耗。。。
[编辑] 2 开发环境准备
根据您的系统,选择如下快速指南:
- Getting Started with Noduino SDK on Linux
- Getting Started with Noduino SDK on Mac OS X
- Getting Started with Noduino SDK on Windows
[编辑] 3 硬件准备
此传感器为 I2C 接口,Falcon 接线方式如下:
- Sensor_SCL --> Noduino_Falcon_D9
- Sensor_SDA --> Noduino_Falcon_D8
- Sensor_3V3 --> Noduino_Falcon_3V3
- Sensor_GND --> Noduino_Falcon_GND
NodeC / SmartNode 接线方式如下:
- Sensor_SCL --> SmartNode_IO5
- Sensor_SDA --> SmartNode_IO4
- Sensor_3V3 --> SmartNode_3V3
- Sensor_GND --> SmartNode_GND
[编辑] 4 编译烧写
进入你的 pcf8563 目录:
$ cd /PATH/TO/noduino-sdk/examples/noduino/pcf8563
编译、上传一步完成:
$ make flash
不同平台下,你的串口设备号可能不一样,确认一下你的串口设备,Linux 下 Falcon 开发板可能被识别为 /dev/ttyUSB1(dmesg 查看),则:
$ make flash ESPPORT=/dev/ttyUSB1
Windows 下 Falcon 开发板可能被识别为 COM6(控制面板 --> 设备管理器里查看),则:
$ make flash ESPPORT=COM6
[编辑] 5 查看结果
上传完之后,用串口工具,用 115200 的波特率打开串口,即可看到串口在持续输出传感器测得的值:
Windows 下可用串口调试助手这类插看
Linux 下推荐使用 picocom:
$ sudo apt-get install picocom $ picocom -b 115200 /dev/ttyUSB1 picocom v1.7 port is : /dev/ttyUSB2 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv imap is : omap is : emap is : crcrlf,delbs, Terminal ready ...... ......
Ctrl + a q 退出 picocom
[编辑] 6 代码示例
#include "noduino.h" #include "pcf8563.h" irom void setup() { serial_begin(115200); pcf8563_init(); pcf8563_set_from_int(2016, 8, 28, 12, 0, 0); serial_printf("PCF8563 RTC Example!\r\n"); } void loop() { pcf8563_now(); pcf8563_print(); delay(2000); }
[编辑] 7 扩展阅读
- 更多问题参考: