Noduino SHT2x

来自Jack's Lab
跳转到: 导航, 搜索

目录

1 开发环境准备

根据您的系统,选择如下快速指南:




2 硬件准备

此传感器为 I2C 接口,Falcon 接线方式如下:

  • Sensor_SCL --> Noduino_Falcon_D9
  • Sensor_SDA --> Noduino_Falcon_D8


  • Sensor_3V3 --> Noduino_Falcon_3V3
  • Sensor_GND --> Noduino_Falcon_GND


NodeC / SmartNode 接线方式如下:

  • Sensor_SCL --> SmartNode_IO5
  • Sensor_SDA --> SmartNode_IO4


  • Sensor_3V3 --> SmartNode_3V3
  • Sensor_GND --> SmartNode_GND



3 编译烧写

进入你的 sht2x 目录:

$ cd /PATH/TO/noduino-sdk/examples/noduino/sht2x/


编译、上传一步完成:

$ make flash

不同平台下,你的串口设备号可能不一样,确认一下你的串口设备,Linux 下 Falcon 开发板可能被识别为 /dev/ttyUSB1(dmesg 查看),则:

$ make flash ESPPORT=/dev/ttyUSB1


Windows 下 Falcon 开发板可能被识别为 COM6(控制面板 --> 设备管理器里查看),则:

$ make flash ESPPORT=COM6



4 查看结果

上传完之后,用串口工具,用 115200 的波特率打开串口,即可看到串口在持续输出传感器测得的温度湿度值:


Windows 下可用串口调试助手这类插看


Linux 下推荐使用 picocom:

$ sudo apt-get install picocom
$ picocom -b 115200 /dev/ttyUSB1
picocom v1.7

port is        : /dev/ttyUSB2
flowcontrol    : none
baudrate is    : 115200
parity is      : none
databits are   : 8
escape is      : C-a
local echo is  : no
noinit is      : no
noreset is     : no
nolock is      : no
send_cmd is    : sz -vv
receive_cmd is : rz -vv
imap is        : 
omap is        : 
emap is        : crcrlf,delbs,

Terminal ready

......
......


Ctrl + a q 退出 picocom




5 代码示例

#include "noduino.h"
#include "sht2x.h"

void setup()
{
	serial_begin(115200);
	serial_printf("Start to test SHT2x sensor!\r\n");
	wire_begin();
}

void loop()
{
	char t_buf[8];
	char h_buf[8];

	sht2x_reset();
	serial_printf("After reset, User Reg = 0x%x\r\n", sht2x_read_reg());

	dtostrf(sht2x_GetTemperature(), 5, 2, t_buf),
	dtostrf(sht2x_GetHumidity(), 5, 2, h_buf);
	serial_printf("Temperature(C): %s\r\n", t_buf);
	serial_printf("Humidity(%RH): %s\r\n", h_buf);

	sht2x_setResolution(0x81);
	serial_printf("After set resolution, User Reg = 0x%x\r\n", sht2x_read_reg());

	dtostrf(sht2x_GetTemperature(), 5, 2, t_buf),
	dtostrf(sht2x_GetHumidity(), 5, 2, h_buf);
	serial_printf("Temperature(C): %s\r\n", t_buf);
	serial_printf("Humidity(%RH): %s\r\n", h_buf);

	delay(5000);
}




6 扩展阅读

更多问题参考:








个人工具
名字空间

变换
操作
导航
工具箱