查看Raspberry的源代码
←
Raspberry
跳转到:
导航
,
搜索
因为以下原因,你没有权限编辑本页:
您刚才请求的操作只有这个用户组中的用户才能使用:
用户
您可以查看并复制此页面的源代码:
== Login == <source lang=bash> Username: pi Password: raspberry </source> <br> == Image == === Raspberry 3 === * Raspbian-4.1 * raspberrypi-jessie-WAZIUP-demo.dmg.zip * <source lang=bash> $ sudo dd bs=1m if=2019-04-08-raspbian-stretch-lite.img of=/dev/rdisk2 conv=sync </source> <br><br> == Pinout == === Model A and B === [[文件:Rasp-gpio-pins-1.jpg | 600px]] [[文件:Raspberry-1-gpio-led.png]] [[文件:Rasp-gpio-pins-2.png | 600px]] [[文件:Rasp-gpio-pins-3.png | 600px]] <br><br> === Models A+, B+, PI 2 B, PI 3 B === [[文件:Gpio-pins-pi2.jpg | 900px]] [[文件:Gpio-numbers-pi2.png | 900px]] [[文件:Physical-pin-numbers.png | 900px]] [[文件:Raspberry-pi-pinout.png | 900px]] <br><br> == Serial == === Enable === <pre> /boot/cmdline.txt "console=serial0,115200" /boot/config.txt enable_uart=1 </pre> <br> === Disable === Remove "console=serial0,115200" from /boot/cmdline.txt If you want to use the uart as IO device, add "enable_uart=1" into /boot/config.txt Or you can do it by run "sudo raspi-config" , enter "Advanced Options" and then enter "Serial" .... <br> === Connections === * RASP_TXD --- HEX_TX * RASP_RXD --- HEX_RX <br> == GPIO Control == * https://github.com/joan2937/pigpio * raspi-gpio * RAW: http://www.pieter-jan.com/node/15 * https://makezine.com/projects/tutorial-raspberry-pi-gpio-pins-and-python/ <br><br> == Timezone == <pre> $ cat /etc/timezone Etc/UTC $ sudo echo "Asia/Shanghai" > /etc/timezone </pre> add following into /etc/profile: <pre> TZ=Asia/Shanghai export TZ </pre> $ sudo reboot <br><br> == Static IP == add following into /etc/dhcpcd.conf: <pre> interface eth0 static ip_address=192.168.1.45/24 static routers=192.168.1.1 static domain_name_servers=192.168.1.1 </pre> <br><br> == ESP8266/ESP8089 == [[文件:Raspi-esp8089.png]] Note that the CH_PD signal is connected to the ID_SD signal. This must be mapped as a GPIO (GPIO0) and switched to an output and driven low then switched to an input again before the driver is loaded in order to reset the module. This will be added in the near future in the driver. https://github.com/al177/esp8089 https://hackaday.io/project/8678/instructions?page=1 <br><br> == Reference == * [[Raspberry精要]] <br><br><br><br><br><br> <br><br><br><br><br><br>
返回到
Raspberry
。
个人工具
18.188.99.178
该IP地址的讨论
登录
名字空间
页面
讨论
变换
查看
阅读
查看源代码
查看历史
操作
搜索
导航
首页
社区专页
新闻动态
最近更改
随机页面
帮助
工具箱
链入页面
相关更改
特殊页面