ESP32 Partical
来自Jack's Lab
（版本间的差异）
(→PIN) |
(→Schemmatics) |
||
| 第25行： | 第25行： | ||
[[文件:Sharp.gy1010.circuit.gif]] | [[文件:Sharp.gy1010.circuit.gif]] | ||
| + | |||
| + | <br><br> | ||
| + | |||
| + | == Quick Start == | ||
| + | |||
| + | === Build === | ||
| + | |||
| + | <source lang=bash> | ||
| + | $ sudo apt-get install git wget make libncurses-dev flex bison gperf python python-serial | ||
| + | $ wget https://dl.espressif.com/dl/xtensa-esp32-elf-linux32-1.22.0-59.tar.gz | ||
| + | $ mkdir -p toolchain | ||
| + | $ tar zxf xtensa-esp32-elf-linux32-1.22.0-59.tar.gz -C toolchain | ||
| + | $ export PATH=$PATH:`pwd`/toolchain/xtensa-esp32-elf/bin | ||
| + | $ | ||
| + | $ git clone --recursive git://github.com/icamgo/esp-idf.git | ||
| + | $ export IDF_PATH=`pwd`/esp-idf | ||
| + | $ cd esp-idf/examples/09_adc_read | ||
| + | $ make menuconfig | ||
| + | $ make -j2 | ||
| + | </source> | ||
| + | |||
| + | <br><br> | ||
| + | |||
| + | === Connections === | ||
| + | |||
| + | [[文件:Quantum-adc1-1024.jpg | 600px]] | ||
| + | |||
| + | |||
| + | To test the ADC pin of ESP32 on Quantum: | ||
| + | |||
| + | * Connect the Quantum_IO35 to 3V3 (measure the power voltage) | ||
| + | * Connect the Quantum_IO34 to GND (measure the GND voltage) | ||
| + | * Connect the Quantum_IO36 to GND | ||
| + | |||
| + | <br><br> | ||
| + | |||
| + | === Upload === | ||
| + | |||
| + | <source lang=bash> | ||
| + | $ make flash | ||
| + | </source> | ||
| + | |||
| + | You need to press the RST buttom after uploading the firmware into flash. If you guys do not like to do this please patch the /path/to/esp-idf/components/esptool_py/esptool/esptool.py : | ||
| + | |||
| + | <source lang=bash> | ||
| + | diff --git a/esptool.py b/esptool.py | ||
| + | index 755f4cb..ff92c91 100755 | ||
| + | --- a/esptool.py | ||
| + | +++ b/esptool.py | ||
| + | @@ -197,6 +197,12 @@ class ESPLoader(object): | ||
| + | + '\xc0' | ||
| + | self._port.write(buf) | ||
| + | |||
| + | + def reset_to_app(self): | ||
| + | + self._port.setDTR(False) | ||
| + | + self._port.setRTS(True) | ||
| + | + time.sleep(0.05) | ||
| + | + self._port.setRTS(True) | ||
| + | + | ||
| + | """ Calculate checksum of a blob, as it is defined by the ROM """ | ||
| + | @staticmethod | ||
| + | def checksum(data, state=ESP_CHECKSUM_MAGIC): | ||
| + | @@ -1421,7 +1427,6 @@ def dump_mem(esp, args): | ||
| + | sys.stdout.flush() | ||
| + | print 'Done!' | ||
| + | |||
| + | - | ||
| + | def write_flash(esp, args): | ||
| + | """Write data to flash | ||
| + | """ | ||
| + | @@ -1503,6 +1508,7 @@ def write_flash(esp, args): | ||
| + | if args.verify: | ||
| + | print 'Verifying just-written flash...' | ||
| + | verify_flash(esp, args, header_block) | ||
| + | + esp.reset_to_app() | ||
| + | |||
| + | |||
| + | def image_info(args): | ||
| + | </source> | ||
| + | |||
| + | Then Quantum can reset to run your app automatically after uploading the firmware into flash | ||
| + | |||
| + | |||
| + | === Checking Output === | ||
| + | |||
| + | <source lang=bash> | ||
| + | $ picocom -b 115200 /dev/ttyUSB0 | ||
| + | ...... | ||
| + | ...... | ||
| + | </source> | ||
<br><br> | <br><br> | ||
2016年11月20日 (日) 01:36的版本
目录 |
1 Overview
Sharp GP2Y1010AU0F partical sensor
2 Connections
Sharp pin 1 (V-LED) => 150ohm resister => Quantum_VIN_3V3 Sharp pin 2 (LED-GND) => Quantum_GND Sharp pin 3 (LED) => Quantum_D8_IO22 Sharp pin 4 (S-GND) => Quantum_GND Sharp pin 5 (Vo) => Quantum_I36 Sharp pin 6 (Vcc) => Quantum_VIN_3V3
3 Schemmatics
4 Quick Start
4.1 Build
$ sudo apt-get install git wget make libncurses-dev flex bison gperf python python-serial $ wget https://dl.espressif.com/dl/xtensa-esp32-elf-linux32-1.22.0-59.tar.gz $ mkdir -p toolchain $ tar zxf xtensa-esp32-elf-linux32-1.22.0-59.tar.gz -C toolchain $ export PATH=$PATH:`pwd`/toolchain/xtensa-esp32-elf/bin $ $ git clone --recursive git://github.com/icamgo/esp-idf.git $ export IDF_PATH=`pwd`/esp-idf $ cd esp-idf/examples/09_adc_read $ make menuconfig $ make -j2
4.2 Connections
To test the ADC pin of ESP32 on Quantum:
- Connect the Quantum_IO35 to 3V3 (measure the power voltage)
- Connect the Quantum_IO34 to GND (measure the GND voltage)
- Connect the Quantum_IO36 to GND
4.3 Upload
$ make flash
You need to press the RST buttom after uploading the firmware into flash. If you guys do not like to do this please patch the /path/to/esp-idf/components/esptool_py/esptool/esptool.py :
diff --git a/esptool.py b/esptool.py
index 755f4cb..ff92c91 100755
--- a/esptool.py
+++ b/esptool.py
@@ -197,6 +197,12 @@ class ESPLoader(object):
+ '\xc0'
self._port.write(buf)
+ def reset_to_app(self):
+ self._port.setDTR(False)
+ self._port.setRTS(True)
+ time.sleep(0.05)
+ self._port.setRTS(True)
+
""" Calculate checksum of a blob, as it is defined by the ROM """
@staticmethod
def checksum(data, state=ESP_CHECKSUM_MAGIC):
@@ -1421,7 +1427,6 @@ def dump_mem(esp, args):
sys.stdout.flush()
print 'Done!'
-
def write_flash(esp, args):
"""Write data to flash
"""
@@ -1503,6 +1508,7 @@ def write_flash(esp, args):
if args.verify:
print 'Verifying just-written flash...'
verify_flash(esp, args, header_block)
+ esp.reset_to_app()
def image_info(args):
Then Quantum can reset to run your app automatically after uploading the firmware into flash
4.4 Checking Output
$ picocom -b 115200 /dev/ttyUSB0 ...... ......
5 Reference
- For more information please refer to
