迷你看门狗
来自Jack's Lab
(版本间的差异)
(→基本布局) |
(→基本布局) |
||
第23行: | 第23行: | ||
== 基本布局 == | == 基本布局 == | ||
− | |||
一个蓝色高亮 LED | 一个蓝色高亮 LED |
2014年12月12日 (五) 14:01的版本
目录 |
1 主控SoC
- Tensilica Xtensa LX3 32-bit RISC SOC clocked at 80 MHz
- 32-bit ALU
- 16, 32 or 64 GPR
- six special purpose registers
- 80 base instructions
The Xtensa ISA employs 24-bit instructions with 16-bit narrow encodings for the most common instructions.
Toolchain 支持:
2 基本布局
一个蓝色高亮 LED
一颗 12V 电池
一个 SPI Flash
一颗 8266
3 Web Server API
3.1 client info
$ curl -X GET http://192.168.1.112/client?command=info { "Version":{ "hardware":"0.3", "software":"0.9.3" }, "Device":{ "product":"Humiture", "manufacturer":"Espressif Systems" } }
3.2 client status
$ curl -X GET http://192.168.1.112/client?command=status { "Status":{ "status":40 } }
3.3 client scan
$ curl -X GET http://192.168.1.112/client?command=scan { "Response":{ "TotalPage":2 } }
3.4 config wifi
$ curl -X GET http://192.168.1.112/config?command=wifi { "Response":{ "Station":{ "Connect_Station":{ "ssid":"HOME-WIFI", "password":"xxxxxxxx" }, "Ipinfo_Station":{ "ip":"192.168.1.112", "mask":"255.255.255.0", "gw":"192.168.1.1" } }, "Softap":{ "Connect_Softap":{ "authmode":"OPEN", "channel":11, "ssid":"ESP_9CCF90", "password":"" }, "Ipinfo_Softap":{ "ip":"192.168.4.1", "mask":"255.255.255.0", "gw":"192.168.4.1" } } }
3.5 config switch
$ curl -X GET http://192.168.1.112/config?command=switch { "Response":{ "status":0 } }
3.6 config light
$ curl -X GET http://192.168.1.112/config?command=light { "freq":0, "rgb":{ "red":0, "green":0, "blue":0 } }
3.7 config reboot
$ curl -X GET http://192.168.1.112/config?command=reboot
3.8 config sleep
$ curl -X POST http://192.168.1.112/config?command=sleep
3.9 设置 station 模式
设备默认为softAP模式,设置 station 模式需先用PC或手机 WiFi 连接到设备,然后从手机或PC端发送下述指令:
$ curl -X POST -H "Content-Type:application/json" -d '{"Request":{"Station": {"Connect_Station":{"ssid":"comcat","password":"12345678"}}}}' http://192.168.1.112/config?command=wifi
设置完成后设备自动重启,进入station 模式,并自动去连接所设置的路由
注:token 字段和espressif 服务器架构相关,是随机的长度为40 的
3.10 设置 softAP 模式
设备发送如下指令,从 station 模式切回 softAP 模式:
$ curl -X POST -H "Content-Type:application/json" -d ' \ {"Request":{"Softap":{"Connect_Softap":{"authmode":"OPEN","channel":6,"ssid":"mini-CamGo","password":""}}}}' \ http://192.168.10.213/config?command=wifi
注意:
- Authmode 支持OPEN、WPAPSK、WPA2PSK、WPAPSK/WPA2PSK。
- password 长度需不小于8 个字符
3.11 恢复出厂设置
$ curl -X POST -H "Content-Type:application/json" -d '{"factory":1}' http://IP/config?command=param
3.12 系统复位
$ curl -X POST -H "Content-Type:application/json" -d '{"reset":1}' http://IP/config?command=param
3.13 获取模块上电运行时间
$ curl -X GET http://IP/config?command=systime
3.14 串口波特率
$ curl -X POST -H "Content-Type:application/json" -d '{" uartbaud":baudrate}' http://IP/config?command=param
其中baudrate 代表要设置的波特率。 { “response”:{ “systime”:11111 } }
3.15 设置dataserver 端口
$ curl -X POST -H "Content-Type:application/json" -d '{" dataport":port}' http://IP/config?command=param
其中port 代表要设置的端口号